Author: admin

Common Mistakes That Occur in Pool Maintenance

We all make mistakes when it comes to maintaining our homes and our pools are not exempt.  When caring for your pool a simple mistake while adding chemicals can take the pool out of commission for weeks.  Unfortunatly however, mistakes in maintaining your pool occur both big and small.

Large mistakes in caring for your swimming pool turn into valuable lessons to learn.  Pool maintenance education is imperative to prevent mistakes and in turn your pool is safer, cleaner, and more efficient without extra frustration on your end.

One of the biggest mistakes pool owners make is with the addition of a chemical commonly referred to as pool shock, a large dosage of chlorine. When dosages of chlorine are too high your pool water will essentially bleach out the color of your clothing.  Although you technically can’t over-shock the pool it can cause issues with more than your clothing.  Too much chlorine can lead to pitted plaster, vinyl liner discoloration, or brittle tile pieces breaking off.

One way to ensure this doesn’t occur is to dissolve the shock chemicals in a bucket of water prior to shocking the pool.  This allows the shock chemical to disperse more evenly throughout the water and in turn protects the pools finish.  As a norm, in pool maintenance a good rule to follow is to dissolve chemicals thoroughly before adding it to the pools water.

Another common mistake when owning a pool that homeowners make is that they don’t take the necessary time or care when brushing and vacuuming your pool.   A good brushing pushes the build up out into the water and settles on the bottom of the pool and then can be vacuumed up. Take the time to brush behind all those hard to reach places like pool ladders, steps, and stairs.  Corners, crevices, and water lines especially in plaster pools should be scrubbed really well.

Pool chemicals are a huge source of the mistakes made by homeowners when caring for their pool.  Your pools plaster can literally be destroyed if the chemicals in the water are not properly balanced.  Don’t ignore your pools pH and alkalinity levels.  A low pH indicates acidity and a high pH indicates alkalinity, too much of either one is bad for your pools plaster. Too low of a pH can damage the equipment used in the pool such as a pool pump and filter, plaster or vinyl linings, heaters, automatic pool cleaners and more.  Proper water chemical balance in a pool is easily accomplished by testing your pools water on a regular basis and making adjustments as needed.

Pound Pool Plastering offers several options when it comes to servicing your pool including plaster, caulk, tiling, cement decks, plumbing, and coping in both commercial and residential settings.  More information can be found at http://www.pound-pool-plastering.com/.

Making Your Home Accessible With a Wheel Chair Ramp

Making your home more accessible for handicapped aids like wheelchairs is a must for many of people with either disabilities or for the elderly. Typically the first step to make in a lack of mobility situation is to install a wheelchair ramp.  Having a ramp installed on your home will improve a person’s life tremendously by entering and exiting the house freely and independently with little to no help from other members of the family.

There are many options for installing or building a wheelchair ramp that can be quite easy to accomplish and have a few options to consider. One choice you can decide on is to take the route of DIY and have the family join together for a weekend project or option #2 is to hire a professional to install one for you. No matter your choice of individual you decide to complete the job, there are some key elements to building and designing the ideal wheelchair ramp for you.

Choosing a ramp that’s right for you

Each accessibility ramp is unique and choosing one that is the right fit for your needs is most important. There are many factors to consider when finding the perfect wheelchair ramp for your home. First question to ask your self is; what type of mobile aid(s) will the person use? Also, there is a chance that the mobile aid that the person is currently using could evolve and change over time. Maybe they currently use a cane or walker but as the years go on, a person may need to switch to a wheelchair as they continue to age.

The next question to consider is; what entrance of the house is the accessibility ramp going to be installed on? Some homes will have obstacles that need to be taken into consideration such as landscape features that will need to be built around. It is also important to check with any zoning requirements in your area through the township or HOA that may require special requirements. Next, deciding on the material you want to use in the construction of the ramp needs to be chosen. Your budget and preference on whether function is more important than curb appeal will help in these decisions. Also Depending on the material chosen, this may or may not make it harder to move at a later time if the ramp is not intended on being a permanent fixture on the home. Lastly, a question to ask yourself about your unique ramp is; how much time do you want to put into construction? It is sometimes best to consult a professional contractor to complete the ramp installation.

Designing the Ramp

The design and requirements of your ramp will be unique because of the factors such as layout of the home or yard and the height needed for ramp. A short ramp would do perfect for a situation with only a couple steps or less than 3 foot incline but if your home is higher off the ground, a ramp will need to be designed with platforms so the incline is not so steep. Platforms are flat landing areas that help break up a ramp to allow the incline to only reach 30 inches. The Recommendation from ADA (Americans with Disabilities Act) that platforms are minimum 60 inches square in order to allow a user enough space to turn in a wheelchair as needed. This also allows a person to stop moving and take a break when needed. Platforms also assist in navigating around obstacles or allow ramps to fit in smaller areas.

The width of the wheel chair ramp is another important aspect to measure for your design. It is recommended by ADA a minimum of 36 inches in between hand rails. This specific measurement should allow even manual wheelchairs the ability to fit comfortably. A reminder to measure in between the closest part of hand rail not at the base otherwise it could cause a person in wheelchair to hit their elbows on the railing if too close.

Guidelines are put into place by ADA to insure that the utmost safety is guaranteed. If working with a contractor, be sure they are building your ramp to be ADA compliant in order to successfully build and design a ramp with safety in mind. If installing a ramp at a business and is not ADA compliant, you can expect it to lead to fines in future as well. Some of these guidelines include: no- skid surfaces, handrails on both sides for any ramp longer than 6 inches, platforms installed if ramp is over 30 feet, and at least a 2 inch flange on bottom sides of ramp to prevent slipping off.

Ramp Materials

Two materials that you can choose from when building your ramp is either wood or metal. Of course with every option, each has their advantages and disadvantages. In the end, no matter the material you choose a ramp should be secured strongly to the ground and anti slip surface added. Taking a closer look at wood ramps, they are typically used in a permanent setting and if built correctly they can last for many years and add true value to your home. The surface of the decking is very important to ensure it is non slip. If ramp is made with a bad type of wood, it will quickly become very slippery in wet weather for everyone using it not only for the disabled. Make sure to do your research on companies who produce ADA-compliant composite materials such as Trex Accents that help increase traction on its surface.

When taking a look at metal for material of choice on your wheel chair ramps aluminum is a top contender. A primary advantage of metal as your material is the ease of installation. Some installs can be done in an hour and also easily removed and transported to a new home if and when needed. If needing a more complex design, metal ramps are great options for this as well and can be custom designed with platforms. The overall appearance of a metal ramp is much pleasing to your curb appeal but there are some that have been designed to look less medical looking.

Prebuilt or Custom Wheelchair Ramps

There are several companies through medical supply or home improvement stores that can assist when choosing a pre-built ramp that is ready to be installed and can be easier route for many compared to building new from scratch. On the other hand, if deciding to build and design your own wheelchair ramp it can be a cost savings on materials but will take more time than installing a pre- built option. Another great advantage of a custom ramp is that is can fit an individuals needs and overcome any special challenges. Hiring a professional contractor to help with your ramp needs will save you time and make this project much less stressful from start to finish.

Glen Miller the Home Doctor is a licensed general contractor servicing Livingston County and the surrounding areas.  Glen offers a wide range of services including home maintenance plans, age in place remodeling, kitchen and bathroom remodeling, finished basements, and hardwood floor refinishing.  More information can be found online at https://www.glenmillerthehomedoctor.com/.

A Fresh Financial Start


Each year when the New Year rolls over, we all begin to think of New Year’s resolutions and how we want to improve our lives from the previous year. We start to set goals for our future to improve certain aspects of our lives whether it is health, personal hardships, or financial difficulties. We sometimes take a step back and realize life did not take us down the path we were expecting to be on and instead of sitting back and relaxing on a beach somewhere we are stuck with piling personal debts from student loans, credit cards, home foreclosure and are now feeling the sting of bankruptcy. Making the first steps after bankruptcy can sound difficult but you can and will bounce back from it and below are some tips on how to get started.

Let Go of Your Shame and Negativity

When hearing the word “Bankruptcy” we instantly are given such a negative image of this situation. Growing up, we are taught what obligations and responsibilities we have and as adults, we pay our bills no matter the circumstance. Unfortunately, life is never that simple and the honest truth is that it is not always possible to repay all of our debts even when trying our best to do so. If thinking that bankruptcy is your only answer, you are not alone. The fastest growing group of bankruptcy filers is people older in life. A study done in May 2011 by University of Michigan Law School found that 1 in 8 adults in the U.S. which is about 13% of general population have thought about filing for bankruptcy.

Even when people know that bankruptcy is a common practice, people still can’t help but feel guilt and disappointment when filing. The best advice is to turn those negative emotions into a more purposeful thought and think of bankruptcy as a learning experience. Truly take the time and look at what you could have done differently to prevent this situation from occurring. The next step is to accept your failure and free yourself by forgiving your mistakes and start to move on.

Recovering From Foreclosure

Studies done by AARP’s Public Policy Institute shows a record amount of homeowners above the age of 50 that went through foreclosure or at least 90 days or more overdue on house payments from 2007 through 2001. One of the biggest issues after losing your home is a good chance you have probably drained most of your savings as well. Some people may never want to own a home again and are content just renting the rest of their life but one way to bounce back from foreclosure is to start rebuilding your savings account or rainy day funds. These accounts typically have $500- $2000 saved in them. The reason of having this type of account is to help deal with emergency or unexpected expenses like a car or home repair that suddenly needs attention. Without this type of savings, you would be forced to use payment options like credit cards to pay everyday expenses that will in turn make you overuse them and hurt credit even further.

Setting Up an Emergency Fund

An Emergency fund differs from a rainy day mainly by being a larger amount saved in a separate account. This account should accumulate anywhere between $3,000 and $10,000 or above if can afford it. The reason for this larger amount saved is for this fund to assist you longer term if something should occur in a personal dilemma such as losing your job or medical issues arise for example. An emergency fund can also help you in a financial disaster such as a bad business investment or loaning money to a family member that never got repaid. These funds should have enough money saved to be able to keep you afloat for 3 to 6 months by paying all your current bills in that time frame. Of course it will take time and energy to make a savings such as this but is a important goal to have in mind.

Get Help From the Professionals

Investment mistakes whether it is watching your 401(k) change drastically or you invest in a friends/ family’s business that doesn’t make it will always take a toll on your confidence. If you are uncertain and nervous on how to manage your assets, it may be best to consult with someone who specializes in this field like a financial planner. A professional can help evaluate your needs and develop a plan to guide you through your financial plan and set new goals after a setback has occurred.

Repairing your credit after divorce

Divorce’s can be very draining on an emotional standpoint as well as financially. Once the worst part is over, you can start to move on from this set back as well. To start fresh from a financial view, you will first need to reestablish your credit in your own name. You can find where you stand credit wise by obtaining a credit report from three of the credit bureaus- Equifax, Experian and TransUnion. Secondly, it is best to get rid of any joint credit accounts with previous spouse and be sure to pay all new bills on time to sustain your credit rating. Some people may not have very much credit in their own names so it may be a good idea to look into a secured credit card. These types of cards need to be paid cash up front for the credit line. It can be somewhat surprisingly how quickly after filing bankruptcy an bank will allow regular unsecured credit cards mainly because lenders know that a user can not file for bankruptcy protection again for several years.

 Bohikian Law Group specializes in bankruptcy services including chapter 7 and 13 bankruptcy.  More information can be found at https://bohikianlaw.com.



Preserving Your Water Softener Brine Tank

Hard water is known to contain higher than normal levels of calcium and magnesium.  This causes issues with lime scale build up that interferes with household and daily functions.  Issues range from clogged plumbing to soap’s ability to clean properly.  For most homeowners the installation of a water softener system is vital in bringing higher quality water to the household.  Most water softening units will continue to function for years with little maintenance.  Regular check ups and cleaning does help to improve their lifespan.

One important aspect in maintaining your water softening equipment is caring for the systems brine tank.  In order to properly maintain the tank, the salt levels should be checked and if low replaced on a monthly basis. Salt is essential in the ion exchange process that takes place in water softeners.  As the system regenerates the hard water will flow through resin in the softener and the hard ions trade place with the soft ions on the resin beads.  This creates soft water.

Your specific softener should come with a manual that instructs you on the perfect level for the salt in your brine tank.  Generally, the tank should be kept half way full and three inches above the water level.  High levels of salt can improve the overall efficiency however should be reduced is the salt sticks to the sides of the unit.  If salt is allowed to build up in the brine tank users should carefully separate the salt to avoid thick bridges from forming. 

It is also important that you put the proper water softener salt into the brine tank.  The manual should explain if your system best operates using granular, tablet, or block salt.  Granular is the most common as it easily dissolves.  On top of different types of salt there are grade variances as well.

  • Water Softener Rock Salt: This is a cheaper source of softener salt and therefore contains more impurities.  These impurities often decrease the efficiency of the softener, dirties the tank, and requires more regular cleaning and maintenance than other salt grades.
  • Water Softener Solar Salt: This option is purer than rock salt.  For most water softeners this salt option is chosen by homeowners
  • Water Softener Evaporated Salt: This option is the highest quality grade of water softener salt that can be purchased.  It is also the most expensive.

If a salt bridge occurs, it is important that it is broken up and not allowed to “build up”.  A solid layer of brine known as a bridge occurs when the salt in the brine tank binds together preventing loose salt on top from mixing with the water below the bridge. This of course prevents the softener from properly functioning.  These bridges can be broken up using a large broom handle and tapping it around the tank several times. If the layers are not easily broken with a long handle a homeowner can pour hot water over the bridge.  If bridges become a common issue in your water treatment system you can try using less softener salt which would allow the salt to drop between refills.  Cleaning out the brine tank also helps.

Another common issue with salt inside of brine tanks is that the salt can become a mushy pile at the base of the tank.  This causes the water to rise around the salt instead of mixing in with it.  A large broom handle can be used to break up the mush mound.  Mush should be scooped out, dissolved in a bucket of hot water, and then poured back into the water softener tank. 

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditioners, water filtration and purification, reverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.

Proper Maintenance Increases The Lifespan Of Your Roofing Materials

Let’s face it, your homes roof is not an everyday priority.  As homeowners we lose sight of the essential exterior elements that are important in safeguarding the interior of our homes.  It is crucial however, that we do take the maintenance and care of our homes roof serious. Asphalt shingle roofing is designed to protect your home. In order for it to perform its job regular roof inspections are needed to ensure it is functioning properly.  Inspections of your homes roof should be done twice a year.  Maintenance and repairs should follow when necessary.  This will allow your roof to remain at peak performance.

Professional roofing contractors are experts at identifying issues with your roof that will lead to interior issues with your home.  It is important to hire a professional contractor to inspect the exterior elements of your home at least once every few years. It is crucial that you as a homeowner take time during the spring and fall seasons to do your own roof and exterior home inspection.

Considerations with Your Roof

  • Before you purchase a home, it is crucial to have the home inspected and a roof assessment performed.  A professional roofing contractor will inspect and report on the future of your roof.  This information gives you insight on repairs that are needed immediately, will be needed in the future, and how much longer you have before a full roof replacement is required.
  • When looking at the exterior of your home and are considering renovations remember to take a look at the landscape. Trim branches and large trees that overhang your roof.  This will prevent the shingles form scratching and gouging roofing materials.  Trimming back trees and branches helps to prevent damaging and puncturing the materials used on your roof.
  • Keep your homes gutters clear.  This is especially important during the winter season to help prevent roof damns from occurring during the thaw and freeze that occurs throughout the season.  If leaves and debris are allowed to build up, your gutters will no longer freely flow, and these backups will occur.
  • Allow your roof to breathe by adding in proper ventilation if it is not already set up correctly.  Heat and moisture needs to be released from the roof to prevent the sheathing and rafting to breathe.  Without this in place the roof with buckle and the insulation will lose its effectiveness.  This causes the roof system to be ineffectual.
  • Proper insulation protects the longevity of your homes roof.  Your home needs protection from heat gain and loss.  The most ideal situation is to include a gap-free layer of insulation on the attic floor along with vapor retarder under the insulation next to the ceiling.  This will help stop the moisture from rising into the attic.  Properly placing vents in the roofing will allow air to pass freely which also helps to prevent issues with your roof.
  • Roofing is prone to the build up of debris, streaks, mold, algae and fungus.  When left untreated this causes a great deal of deterioration in the materials on your roof which in turn shortens the roofs lifespan.  One method that is effective in preventing these issues is to install zinc strips along the roof ridge.  The zinc will protect against the growth of fungus, moss, mildew and algae. 

Your homes roof is the most important element in creating structural integrity of your home. Taking time to do bi-yearly inspections will help preserve and protect your home for years to come.

As a full-service home improvement contractor servicing all Southeast Michigan, Kearns Brothers, Inc. offers clients a wide range of services to meet their construction needs including: roofing, siding, window, masonry, chimneys, gutters, and insulation services.  More information can be found at www.kearnsbrothers.com.

Maintaining Large Scaled Medical Equipment While Cutting Costs

The pressure is high for the leaders of medical facilities to keep up on the changing technology of medical equipment, improve the quality of patient care, and reduce costs of medical equipment maintenance and care. Creating a cost saving strategy in medical equipment maintenance allows facility leaders to stay ahead of their competition without budget concerns.  One way many healthcare facilities have chosen to do this is through outsourcing.  This allows medical facilities to purchase service and repair contracts from companies that specialize in the service and repair of large scaled medical equipment such as linear accelerators and CT scanners. 

Healthcare centers rely on medical equipment to provide the highest quality of care to patients at all times.  It is crucial that your facility have a system in place to manage, maintain, and repair high end, technologically advanced medical equipment like LINAC.  This can be done simply by contracting services through an OEM or third-party service provider.  Facilities must have a strategy in place that fits their exact needs including both maintenance and repair.

Considerations in Medical Equipment Service Contracts

When you are purchasing a contract, it is important to make sure you know exactly what is and what is not covered.  Full-service contracts, through an OEM or third-party provider should normally provide parts, labor, and preventative maintenance.  Analyze your facility’s medical equipment needs.  Ask yourself the following:

  • What times of the day is equipment used for patient care?
  • Are back-up systems available if the main piece of equipment is down?
  • How old is the current equipment? What is the service history of the equipment?

Ways Facilities Can Save When Contracting an OEM or Third-Party Provider

  • Choose an 8 am to 5 pm, Monday-Friday option for service and maintenance.
  • Combine equipment and facilities into a single contract.

In-House Strategies to Support Contracted Services

Even with contracted services there should be an in-house program to support it.  There are quite a few cost saving strategies including the assessment of available staff, the competency of your staff, the history of equipment, and the level of risk the hospital wants to assume.

  • Determine your staff’s availability and capability.  The staff should attend training and expectations of the level of support to be given for each piece of equipment should be determined.
  • Do a complete cost/benefit analysis between a full-service contract vs a combination of contracted services and staff maintenance.  Remember to consider the costs associated with training, parts, and additional tools/equipment that would be needed.
  • Review the historical data on the expense of labor and parts for each piece of equipment.  This will help you determine the cost of parts and labor under contract if you wouldn’t have had a contract in place vs having the contract in place.

As mentioned earlier there are a number of different medical equipment service, maintenance, and repair plans beyond full-service contracts. These include:

  • Preventive Maintenance Contract
  • Parts Only Contract
  • Biomed Support Contract

After doing research and analysis on your existing equipment you should have a good idea on which type of service contract best suits your company.  Linear accelerator maintenance, repair, service, and parts will obviously cost more than then the same services on a hospital bed.  These are the things that facility leaders need to account for when contracting with an OEM or third-party service company.

As an independent LINAC service company, Acceletronics is dedicated to delivering the best equipment performance and services for linear accelerators and CT scanners across all major brands and models, as well as new and refurbished LINAC systems for sale.  More information can be found online at https://www.acceletronics.com/.

Improving Your Business With Google Ads

Google Ads is a form of paid advertising through the search engine, Google.  Ads are shown to users based on their searches.  The major benefit of using Google Ads is that consumers are seeing ads targeted to their searches while they are actively searching for your good or service.  Google Ads makes up for over 40% of the digital ad revenue for the entire world. 

Internet presence makes or breaks businesses throughout a number of industries.  Marketing professionals must transition from traditional marketing methods to digital marketing methods such as Google Ads to preserver. This situation makes the internet cluttered with intense competition.  Both businesses and consumers rely on the internet in making purchasing decision, product research, and more.

Benefits Google Ads Can Have on Your Business

Improved Brand Awareness

In the past brand awareness between business and consumers came from a variety of methods including newspaper, billboards, radio, and television advertisements.  This was a great method of marketing between business and consumers however left business to business advertising suffering.  Digital marketing, specifically through Google Ads, has transformed the way in which we create brand awareness within the marketplace.

Google Ads allows brands to advertise to targeted audiences that are researching specific products or services using specific keywords or keyword phrases that relate to the advertising business. Brand awareness is one of the many benefits businesses have advertising on Google Display and Search networks.

Quicker Than SEO

Google Ads works faster than search engine optimization.  SEO is a slow, methodically way in which to increase your organic presence online.  For businesses looking for a long-term presence within search engine rankings benefit from a combination of both organic and paid advertising.  Google Ads allows businesses to pay for visibility in the form of Google Ads amongst top competitors.   They allow your business to advertise directly to a target audience that is actively seeking out your products or services. 

Google Ads brings brand awareness about faster than traditional SEO methods.  There is a tremendous amount of competition with paid advertising.  The benefit however is that the business owner is in complete control of the amount they are willing to bid for top positions of their ads. A number of elements go into the amount each of the clicks on your ads will cost as well as the position at which your ad will sit on Google Search Networks or Google Display Networks.  These include: Keywords Quality Score, Ad Relevancy, Landing Page Relevancy, and Expected Click Through Rate.

Google Ads is beneficial for a number of reasons including:

  • The Ability to Outrank Competitors Ads
  • The Ability to Influence Audiences to Make a Purchase
  • The Ability to Increase Brand Visibility to a Targeted Audience
  • The Ability to Test Variations of Ads and Keywords
  • The Ability to Create Different Campaigns and Strategies Based on User Demographics
  • The Ability to Schedule Ads to Reach Targeted Audiences at the Right Time
  • The Ability to Remarket to Audiences Who Have Showed Interest

Creative Programs and Systems, CPS, is an all-inclusive IT solutions company offering a variety of services including: managed IT services, IT consulting, residential computer services, custom programming, website design, iphone & android app development, and more.  More information can be found at https://cpsmi.com.

Aluminum Gate Installation Made Simple

The aluminum fence has been purchased and installation is beginning but first you must plan where to put your gate within the fence line.  We can help!

The first step after you have decided where to place the gate is to start by digging the holes for the aluminum posts for your gate. As you are digging the holes you must make sure they are wider and deeper than the holes that have been previously dug for standard posts for the line, end, and corner.   Wider, deeper holes are needed for aluminum gate posts as they will be under heavy usage.  A bigger hole will mean that more concrete can be used when securing the post itself.   When sizing the width of the hole needed for your gate be sure to make plenty of room on all sides of the post for concrete. 

The depth of the hole needs to take into consideration a number of things including the frost line, the post length, the height of the fence, and the width of the gate. Living in an area where a freeze can occur the hole for the gate post should be dug deeper than the frost line.  Having the concrete below the frost line will prevent the footers from cracking over time.  Concrete must be installed at the bottom of the hole as well as around the four sides of the aluminum gate post. 

Once the first hole has been dug it is time to move on to the second hole.  The placement of the second hole will be solely dependent on the width of the gate. Aluminum gates are meant to be opened and closed.  A gate that is four feet has a gate frame of only forty-six and a half inches, the inside measurement, post to post will be forty-eight inches. This gives room for the installation of hinges and latches. 

Next comes the placement of the gate posts and the addition of the concrete.  Concrete should be added to the bottom of the hole before the placement of the post.  This helps to create a strong bond between the concrete and the aluminum gate post. It is important to keep your tape measurer available so that you can make sure your measurements are accurate throughout the installation of the posts and walkway gate. 

Once the post distance is achieved and the posts are leveled it is now time to slowly shovel in more concrete.  This process should be done with extreme care to prevent the movement of the gate post.  Concrete should fill the hole up until you have reached about four to six inches from the top of the hole. On top of the concrete you will add in a final layer of dirt which is packed tightly around the post to create a sturdy base for your gate. Again, throughout this process it is crucial that you maintain proper measurements and that the posts remain level.  The concrete should be allowed to completely set up and dry before the final step of hanging the aluminum gate and the installation of the hardware.

The final step of aluminum gate installation is to determine the direction in which the gate will swing.  Outward swinging gates will need hardware to be installed on the outside face of the fence line.  Vice versa for gates that will be swinging inward.  Hinges will be first installed on the frame of the gate.  In order for even weight distribution measure from the top and bottom of the gate for an even distance for installation of the hardware.  Once the gate hinges are attached to the gate frame it is time to anchor the gate to the posts.  This is a two-person job, one person to pick up the gate and hold it to the post and the other to fasten it down.  Lastly install the latch and there you have it, your aluminum gate will be installed!

iFenceUSA is an online distributor of wholesale aluminum fences and gates for residential, resort, commercial, and industrial installation.  As an industry leader in maintenance-free aluminum fencing products we have all your aluminum fence and gate needs covered.  More information can be found online at https://ifenceusa.com/.

Can An IT Consultant Benefit Your Business?

Business of all shapes and sizes have begun to realize the importance of hiring consultants in the drive to grow their businesses.  A consultant is a person who offers expert advice for an hourly fee.  Often, they have a niche in which they specialize and can provide their expertise along with an outside perspective. Consultants give businesses opportunities to increase their productivity and expand business opportunities.  

One area many companies seek to hire consultants is the world of IT.  Information Technology has changed the way in which society as a whole operates thus its importance in business has increased as well.  IT services transform how businesses operate.  IT consultants are brought in to help businesses keep up with the latest trends in technology.  Efficiency is a key element in business.  IT consultants implement technology throughout business applications to increase effectiveness in all areas of your company.

The Benefits of Hiring IT Consultants in Business

Hiring an IT consultant allows you to focus clearly on core business functions.  There is no doubt that employees are at their best when they are allowed to focus on their intended position.  This is true no matter what industry you are in.  From Teachers to Doctors, Sanitation Specialist to Engineers, when you are allowed to concentrate on your job and only your job, you will be more successful.  Nothing is more frustrating for employees and business owners alike to be distracted from what they are supposed to be doing to focus on a task that is not relevant to them such as technology repair or upgrades.  Hiring an IT consultant allows associates to focus on their core job which increases your bottom line.

Hiring an IT consultant allows you to benefit from a specialist.  Yes, having an IT department does have benefits, when your printer stops printing there is someone on site to instantly handle the issue.  However, the same person that knows how to fix your printer, reboot your computer, and can handle the ins and outs of your current system are not the same as a consultant that comes in, evaluates the overall system and based on experience recommends more efficient solutions to common, everyday operations.  Experienced IT consulting services have likely helped many companies in similar situations to yours.  Having an industry expert guiding your business increases your success while offering you peace of mind.

Hiring an IT consultant allows you to get an outside perspective on your business functions.  We all get stuck in doing things the way in which we have always done them.  For years you may have tracked inventory using pen and paper then inputting it into a program.  This doesn’t mean that this is the most efficient method or even a method that keeps up with the way in which businesses are operating today.  An outside consultant views your business from a whole new perspective than individuals who are immersed in it daily and used to doing things a set way.

Hiring an IT consultant is cost effective. The main “job” of any consultant is to reduce costs and increase efficiency.  Full-time employees are expensive and require a full-time salary, benefits, a work space, and so on.  Consultants on the other hand, are normally hired when a known problem exists and needs to be solved within a very specific time frame which is more cost effective and a better use of employee time.

The list of benefits that come from hiring an IT consultant can go on and on.  If you find that your business has become stagnant and you are looking for growth, hiring a consultant may be just what your business needs.

Creative Programs and Systems, CPS, is an all-inclusive IT solutions company offering a variety of services including: managed IT services, IT consulting, residential computer services, custom programming, website design, iphone & android app development, and more.  More information can be found at https://cpsmi.com.

Key Benefits in Android App Development


There are a number of operating systems that drive mobile devices. When working with clients, mobile app developers must determine what platform to target their app towards unless of course, they have the resources to develop for multiple platforms simultaneously.  The operating systems that your app is programmed for will determine the success or failure of your app.  Android, iOS Apple, Windows, and Blackberry operating systems are all popular platforms.  In this installment we will look into the benefits of programming for Android app development. 

Portability

Android Apps are developed using Java language in program.  Java is a language that can easily be ported to additional mobile operating systems such as Chrome OS, Ubuntu, Symbian, Windows 10 and Blackberry. 

Android Studio

The Android Studio is superb software application that is offers comprehensive services to programmers.  It is specifically designed for Android development and allows for quick and efficient set up of Android Apps.

Java

As mentioned above Android Apps are developed using Java. Java is a programming language that is used in a number of operating systems and a variety of devices.  Programming in Java allows Apps to easily be integrated on other operating systems such as Windows and Linux whereas iOS development is done in Objective C or Swift.

Google Play

Google Android Apps are easily deployed to the Google Play store.  On most occasions they are able to be downloaded by users in hours after being put on Google Play.  Another feature of the Google Play store is nice is that developers are able to release apps as an alpha and/or beta release. Doing this allows the app to be released only to select members or a group of testers. 

Ease of Entry

Android App development can be done on Windows, Mac, and Linux.  A one-time fee of $25 allows individuals to register as an app developer on the Google Play Store whereas development on the Apple App store requires a yearly fee of $99. 

Profitable

Both Android and iPhone Apps are profitable, and both offer the ability for users to make the initial app purchase and in-app purchases. 

Creative Programs and Systems, CPS, is an all-inclusive IT solutions company offering a variety of services including: managed IT services, IT consulting, residential computer services, custom programming, website design, iphone & android app development, and more.  More information can be found at https://cpsmi.com.