Protecting Against Lead in Water

Lead is a naturally occurring element found in the Earth’s crust in small amounts. It can be beneficial in specific uses, but it is a harmful metal to a person’s health and there is no safe level for lead exposure to humans. People are exposed to lead products that range from lead-based paint, air, soil, dust inside homes, food, pottery, and even drinking water. Consuming high levels of this metal can cause health issues once it enters the blood, especially for younger children.

Effects of Lead

The EPA is required by the Safe Drinking Water Act to determine the level of contaminants in drinking water that is considered safe with minimum health effects. The standard allowed for lead is set to zero, and even at low levels, lead can be very harmful and can accumulate in the body over time. Lead is a neurotoxin that can cause brain disorders and severe kidney damage. The effects of lead do not equally impact individuals. The risks will vary depending on the person, the chemical properties of the water, and the amount of lead consumed. Specific issues found in people:

  • Pregnant Women – As discussed above, lead can accumulate in the body over time and can be found in a person’s bones along with calcium. Lead is released from the mother’s bones when maternal calcium transfers to the fetus to help develop bones for the baby. The lead can also cross the placental barrier that can expose the fetus, possibly causing reduced growth and premature birth.
  • Infants and Children – Infants who consume water with lead content may be at a higher risk of exposure since the large volume of water they consume is relative to the proportion of their smaller body size. Children are often vulnerable to lead poisoning due to the fact they drink more water and have developing bodies. High levels of lead exposure can cause convulsions, significant neurological damage, organ failure, coma, and even death. Lower exposure of lead can cause hearing loss, reduced growth, and an increased chance of learning and behavior disabilities.
  • Adults – Adults who are exposed to lead can suffer from health issues such as cardiovascular effects with increased blood pressure and hypertension. In addition, older persons can develop kidney damage and complications with reproductive organs.

How Does Lead Get in Tap Water?

Lead is in all areas of our environment and can be found in the air, soil, and water. Lead can even be found within our homes in certain places. Most lead contaminates come from human activities such as the use of fossil fuels and gasoline, factories, or lead-based paints. When lead is released into the air, it can travel long distances before it settles in soil or water supplies. Lead can merge into drinking water, causing corrosion to take place, and eating away at the piping within homes. In older houses, before 1930, lead was used for soldering pipes. It wasn’t until the early 1980s when we saw a decrease of lead being used for pipes in homes.

Lead Removal

If you suspect that lead may be in your water, we advise that you get your water analyzed by a certified laboratory, or at minimum, purchase a DIY self-test kit to determine for sure. The good news is, lead can be removed from your drinking water. The simplest way to solve this issue is by using the correct water filter after the contamination source is identified. The three basic water filtration methods to remove lead are:

  • Reverse Osmosis – The most popular and inexpensive option, and it can eliminate 95% of lead in water.
  • Activated Carbon Filtration – This option allows the activated carbon in filters to absorb minerals such as lead and magnesium from the water, decreasing the amount of lead supply significantly. However, the disadvantage is that the filter cartridges may fill up quickly and need replacement often. The lead removing capabilities also decrease after a certain amount of water has been passed through the system.  
  • Distillation – This method produces the purest water, but it comes with an expensive price tag and requires a lot of electricity and processing time as well.

The experts at Reynolds Water Conditioning have a solution to your home’s unique water quality needs, including arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more. More information on water treatment solutions, including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal, can be found online at https://reynoldswater.com.

The Importance of High-Quality Drinking Water

Hydration is key to all living things, and without it, we would only live for about five days. Our bodies are more than 50% water and it helps maintain our normal body temperature, lubricates joints, and enables the body to rid waste through urination, sweat, and bowel movements. Doctors advise us to drink at least eight 8 oz. glasses of water every day and studies have shown that women, on average, will consume approximately 91 oz. of water and men will drink about 125 oz. of water every day. Part of this consumption of water is from foods such as fruits and vegetables. It seems quite simple why water is so important to our health, but understanding the different risks from contaminations and how to protect your drinking water can be more in-depth.

Is Tap Water Safe?

In general, tap water is considered to be safe to consume if it comes from a public water system that is run and maintained by a municipality. When drinking water exits a treatment facility and travels to your home, the quality standards must reach strict safety requirements. Unfortunately, even with these safety policies, it does not mean that the water is free of any contaminants, but that the levels of the pollutants are low enough not to cause any health risks. Accidents do happen and if the water supply does become contaminated with something that can create illness, the supplier must inform consumers within 24 hours and offer alternative suggestions for safe drinking water.

Types of Contaminations

There are a few ways that water can become contaminated. Water can contain microorganisms like parasites and bacteria that are added to the water from human or animal feces. It can also become contaminated from industrial waste such as spraying crops that contain chemicals or nitrates used in fertilizers that run off the land. Sometimes the natural deposits from underground can have various minerals like lead or mercury that can enter the water supply. Lead can also transfer to a water source through old lead pipes as well. Even pipes that claim to be “lead-free” can contain as much as 8% lead. To avoid lead consumption when using tap water, use water from the cold tap and to let the water run for a minute before using it.

A Solution to the Problem

Often, when a contamination notice is sent to homes about a water crisis, it is advised to boil your water for 24 to 48 hours, so many consumers are under the impression that contaminates can be removed by heating the water to cleanse it. Boiling water will indeed kill germs; however, contaminants such as lead, nitrates, and pesticides will not affectedly be removed using this method.  It may have an opposite consequence since boiling will reduce the amount of water when it evaporates, making the concentration of the contaminate even higher. There are four main types of water filters that are more beneficial for contaminant removal:

  • Activated Carbon Filters – These can remove organic contaminants that change the taste and smell. Certain systems are designed to remove chemicals such as chlorination by-products, pesticides, and some metals like copper or lead.
  • Reverse Osmosis – This filtration system can remove nitrates, sodium, pesticides, and petrochemicals.
  • Ion Exchange – This type of filter can remove minerals like calcium and magnesium, and they are used in combination with other systems such as carbon absorption or reverse osmosis.
  • Distillation – This method creates distilled water by collecting condensation of steam from boiling water.

The experts at Reynolds Water Conditioning have a solution to your home’s unique water quality needs, including arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more. To learn more information on our water treatment solutions, including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron and odor removal, visit https://reynoldswater.com.



Water Filters 101


Water is one of the most important elements on this planet and without it, we would only live a few short days. Our bodies are made up of roughly two-thirds of H2O and to keep a healthy balance, we need to consume 2.4 liters of water each day. It comes to no surprise that new ways are constantly being found in order to provide us with more clean, pure water to nourish ourselves. In order to remove many of the harmful impurities from our water, the use of water filters is a solution to this problem. How important are water filters you may ask? Let’s take a closer look at what a water filter is.

How Filters Work

Water filters use two different techniques in the removal of dirt and debris. The first is physical filtration in which water is strained by a physical barrier such as a thin gauze or fine textile membrane to remove the larger particles. The second method is done thorough chemical filtration, which involves water passing through an active material, such as carbon, that removes impurities as they pass through chemically. There are 4 primary methods used for water filters that use a combination of physical and chemical filtration:

Activated Carbon Filters

This type of filter is the most common and popular of the options available that are based on charcoal. Charcoal is a form of Carbon that is very porous because it has a big internal surface area that can trap foreign particles. Larger contaminants are stuck on the outside, thus being removed from the water. Carbon can also act as a magnet for items such as lead and VOCs that continue to remove particles internally as water passes through the filter. On the chemical aspect, chemicals like Chlorine are removed during a chemical reaction when water is in contact with Carbon. The main disadvantage of this type of filter is after time it will get clogged with impurities and need to be replaced, which can add additional costs down the road. 

Reverse Osmosis

Filtration that removes contaminants by water pressure to force tap water through a semipermeable membrane is called Reverse Osmosis. The membrane is an effective, very fine filter that allows the water to pass through but the contaminants like Lead, Mercury, and Iron stay behind. The downside is certain items such as some pesticides, solvents, and metals like Chlorine and Radon can not be removed with Reverse Osmosis.

Distillation

A natural option for filtration can be done with the simple process of steam distillation that involves heating water to boiling and then cooling the steam to remove the contaminants. Most contaminants have a higher boiling point than water which is why they are left behind when the water becomes steam. The steam is collected and transformed back to water in a separate container. The disadvantage to this type of filtration is some contaminants such as volatile organic compounds (VOCs) boil at a lower temperature than water and they evaporate with the steam and can remove beneficial minerals in natural water during the filtration process.

Ion Exchange

This filter is very good at softening hard water by removing limescale. The process is done with chemical filtration method by releasing ions, like sodium, and exchange them for unwanted ions like heavy metals found in your water. The result is better-tasting water, however, the sodium is simply another form of contaminant, so the ion exchange doesn’t exactly make the water “pure”. This option is not the best for people on low-sodium diets. The second disadvantage of ion-exchange filtration is that it will need to recharge the filters occasionally with more sodium ions by adding a certain type of salt.

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.



Why You Should Have A Water Filtration System


Without water, we could not live so it’s easy to see why choosing the best source for the cleanest water is an important decision to be made. Industrial chemicals, heavy metals, and pesticides are found in water supplies all over the world and it is up to us to protect ourselves and our families from the pollution we can potentially put into our bodies. The good news is there are many affordable options that are available to produce and improve water quality.

Knowing You Water

The first step to improve your water quality is to know exactly what type of water you are currently dealing with. There are several ways that water testing can be performed some more accurate than others. The most simplistic form of testing is by using your senses of sight, smell, and taste. With sight, you may notice cloudiness or particles that float or if the coloring of red, brown, or orange it could indicate rust from corroded pipes. As for the smell, certain aromas will inform you of chemicals that are in the water such as bleach type which could be chlorine from the local facility. Or perhaps you smell rotten eggs, and this may indicate somewhere through the water’s course there is bacteria growth. Lastly with taste, if the water instantly doesn’t taste normal it is best to never swallow it. The next option for water testing is to have a professional water treatment company to test your water supply or purchase an at-home water test kit. These tests can determine if the water contains harmful materials and reveal the water’s pH and hardness. If your water source is from a private well, it is advised to have the water tested twice a year.

Water Filter Options

Water filters come in a variety of shapes and sizes and each one has unique features that will benefit a home differently depending on your water quality needs.  The first question to ask yourself is what impurities are you wanting to remove from your water? After reviewing your water quality report or speaking to your professional water treatment company, you can decide what type of filter you are needing to use.

  1. Pitcher filter- The simplest water filters to use that fit inside a pitcher that can be kept inside the refrigerator. This style is inexpensive and easy to use but the lifetime is short and typically only removing few contaminants such as chlorine from the water.
  2. Faucet mount filter- this style is exactly as its name implies and is located directly under your faucet. They require little installation with easy replacements and are an inexpensive option. These filters can remove a decent number of contaminants but be sure to research what exactly it can remove to be safe.
  3. Countertop filters- These filters will not take up space under your sink but can however clutter your countertops. They work best for filtering large amounts of water without having to modify any plumbing. Installation can be done hooking to your faucet or be freestanding as well. An advantage is they do not clog as often as a faucet-mounted system but are not compatible with all types of faucets either.
  4. Reverse osmosis– A process where water is forced through a membrane that filters molecules that’s are physically larger than the water molecules. This type of filter is very well at removing minerals however it cannot remove chlorine or volatile organic compounds which are more of a cause for concern so many ROS systems combine prefilters and carbon filters to help this issue.
  5. Whole-house filters- This type of filter is installed directly in the water main and filter all water coming into the home. An advantage is they have a long lifetime and are an inexpensive option for removing sediment, rust, and sometimes even chlorine. Unfortunately, they can not remove most other contaminants, so it is important to pair this with another drinking water filter. They are on the pricier side in relation and must be installed by a professional water treatment company.

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.



Salt Vs Salt Free Water Softeners

A recent debate that is brought up often after water softeners are which systems are better, the salt based or salt free softeners? Several factors will need to be considered when answering this question. In this installment we will look at how both systems work and what advantages/ disadvantages of each to understand which system is best suited in a certain situation.

Salt Based Water Softeners

Taking a closer look at how these products work, these systems are designed to remove hard water minerals like calcium and magnesium from your water which than provided soft water. This process of hard water removal is done through “ion exchange”. Salt based softeners require the use of salt pellets and regeneration periods or a recharge cycle. As a result, these systems will prevent scale buildup, reduce future staining on appliances and laundry, and personal hair and skin softness. They will ultimately save you money by prolonging the life of your water base appliances and use less soap/ detergent when cleaning. If your home has high levels of hard water, this type of softener will be your best choice for your concerns.

Salt Free Water Softeners

Despite their name, salt free water softeners do not soften hard water. They work by crystallizing calcium but does not remove it. Salt free water softeners are more specifically a water conditioner that prevent the hard water from adhering to the surface of an object such as the inside of your water pipes. An advantage of using this type of water softener/ water conditioner is that they do not waste water the same way as traditional softeners. They are also less expensive to operate and require less maintenance. This method of hard water treatment is not as effective as a salt-based system and will not be able to remove high levels of hard water.

Choosing Potassium Chloride

A third option that can be done to remove your hard water issues but will remain on the healthier side would be soften water by using the alternative of potassium instead of sodium. Potassium is an essential mineral that provides good health to people and to the environment. Water conditioning units at Reynolds Water are designed to use potassium just as well as the use of sodium. Simply change the product by changing to a different bag option and your set.

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.



Basic Water Softener Maintenance

Maintenance and service on water softeners is pretty basic when it comes to the world of appliance upkeep.  The exception to this, however, is the initial installation of the water softener.  Determining the water hardness level, regeneration timing parameters, salt to use, and when to refill the salt so the softener can perform properly can be a bit tricky.  Proper water softener set up can make long term maintenance easier and the softener perform more efficiently and last longer.  

Ongoing Maintenance – Tips for Residential Water Softeners

Avoid Salt Bridges

Salt bridges occur when an empty space is created in the brine tank between the water and the salt.  This prevents the salt from dissolving in the water which is how brine is made.  Without brine the resin beads that soften the water are unable to do their job. 

The most common cause of bridges are high humidity, temperature changes, or using the wrong type of salt.  Salt bridges make it appear that the salt in your water softener tank is full.  Your water, however, will be hard because the salt is not dissolving to make brine.  To remove a salt bridge, use a long handle and slowly push the top of the salt downward.  A little bit of pressure is all that is needed to break up the solidified salt.

Prevent Salt Mushing

Salt mushing is more serious than salt bridges.  This occurs when the salt dissolves and then recrystallizes to form a sludge on the bottom or the brine tank.  This thick layer of sludge keeps the softener from cycling properly during the regeneration process.  Hard water remains and a serious blockage is created in the tank.  If you attempt to remove a salt bridge and it does not break up, salt mushing is probably the cause of your hard water problem. The only way to fix the issue of salt mushing is to drain the softener of all water, remove the old salt and sludge, and replace it with fresh salt. 

To prevent both salt bridges and salt mushing it is important to use high quality salt products as they greatly reduce the potential for problems.  Also, it is important not to overfill the brine tank with salt.  Keeping it only half-fill will prevent older salt from sticking to the walls of the softener tanks.  Preventing humidity around the water softener can also help. An environment with high humidity can lead to condensation in the brine tank which will cause salt to bond together.

Water Softener Salt

In choosing salt to use in your water softener you will be able to choose from rock, solar, and evaporated salt.  Rock salt is the cheapest however contains the highest level of insoluble minerals.  When this occurs, the result is a muddy tank which decreases the softening efficiency and leaves impurities in your water.  Solar salt is more soluble than rock salt.  Solar salt is obtained through the evaporation of sea water and is found in crystal and pellet form.  The best option for salt to use in your softener is evaporated salt.  This is obtained through the combination of evaporation and mining.  Solar salt is 99.99% sodium chloride and is the purest form of salt.

Salt with high levels of purity leave less residue thus lower the likelihood of salt bridging and mushing.  Purer salt results in less maintenance and high-quality salt in pellet form helps to eliminate bridging issues. Water softener salt delivery allows you to order top quality salt brand products that address specific issues such as high concentrations of iron, rust stains, and salt free alternatives like potassium chloride. 

Resin Bed Cleaning

Resin beads are routinely recharged by salt, but this doesn’t mean that the resin bed shouldn’t be flushed every few months with a cleaner designed for water softeners every few months to keep it in top shape.  Water softening units can become polluted with iron, silt, metals, and a variety of different organic compounds which decrease your softeners efficiency.  The process to reduce the ineffective resin is fairly simple.  You will pour the manufacturers recommended amount of cleaner down the brine well and manually regenerate the water softener.  The cleaner will be discharged during the normal flushing process during the softening cycle.  This action cleans the resin and helps the absorbency of calcium and magnesium.

Clean the Venturi Valve

The venturi and nozzle work to create suction that moves brine from the brine tank into the resin tank during regeneration.  Sometimes this valve can become plugged up with sand, sediment, or dirt.  A clean valve is imperative for water softening to occur properly.  This can be accomplished by unscrewing the cover of the valve, removing internal parts, and cleaning them all with soap and water.  Completing this process twice a year will help keep the process running smoothly and more efficiently. 

Periodic maintenance, regular upkeep, and monthly checkups all prevent major incidents from compiling and affecting the quality of the water running through your home.  Hard water leads to major expenses, like new appliances, plumbing issues, and more, when left untreated. 

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.



What Do I Need to Know Before Purchasing a Water Softener?

There are several different options when it comes to treating the water in your home.  The decision on whether you choose to install a water softener, water conditioner, reverse osmosis system, water purification, or water filtration system all comes down to the quality of the water from your tap.  Depending on the minerals and contaminants that are in your water the treatment option chosen for installation will vary.  Below are the most commonly asked questions surrounding water softeners and water treatment options.

What is hard water by definition?

All water naturally contains minerals such as calcium and magnesium that dissolve in it.  Water that contains more than one grain of a combination of minerals is considered to be hard.  To determine what level of minerals can be found in your homes water bring a sample from each faucet into Reynolds Water Conditioning Co

What should concern me about having hard water?

One of the biggest concerns when it comes to having hard water is the scaling that occurs in pipes and fixtures.  Scaling occurs when water is heated and minerals re-crystalizing.  These scales then get into appliances that use water such as the washer, water heater, and dishwasher decreasing its lifespan.

Another issue made worse because of hard water is soap scum in showers, on your hair, skin, and even clothing.  Soap combined with hard water forms a scummy substance that accumulates.  Even after rinsing thoroughly soap scum deposits are still present.

Why do I need to soften the water in my home?

When your home has hard water, the installation of a water softener can often help.  Soft water is beneficial for a variety of reasons.  Not only does it prevent scaling, but it also allows you to use less detergent, reduces spotting on fixtures and dishes, helps to increase the longevity of appliances, and more.

Are there reasons I should not use a water softener?

If you are on a low sodium diet, you will want to consider a water softener alternative. Water softeners use a process of ionization using salt to soften hard water. Salt ions attract hard water minerals and deposit them on the water softener resin (simply put of course). Basically, the salt ions and mineral ions trade places with one another which is why the soft water contains extra salt. 

Do I need to soften water outdoors or on my ice maker?

Yes, the water in your ice maker should be softened prior to making ice.  Softened water does not leave scale deposits which water that has not been softened does. 

Irrigation systems are a personal choice.  If water is left untreated there is a high potential for outdoor staining to occur.  Hard water deposits minerals such as iron on to landscaping, siding, and outdoor furniture which overtime discolors the materials. 

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.



Stain Control for the Rust In Michigan Irrigation Systems

Rust is a common element in water that is flowing through Michigan irrigation systems.  One way that homeowners can ensure that this rust doesn’t cause staining to outdoor furniture, landscaping, or siding is to install a water treatment system that offers irrigation stain control.  Reynolds Water Conditioning Company offers a system that is designed specifically for this purpose.  In these systems a concentration of a bio-degradable solution is injected into the irrigation stream as it enters the irrigation system.

Irrigation stain control water treatment systems help to prevent the formation of rust and red water staining outdoors.  The solution that is injected into the water is safe in preventing stains without harmful acids and chlorides.  Not only does the solution prevent staining it protects against corrosion, pitting, and plant life damage. 

Now that we know how we go about preventing future staining it is important that we remove the rust stains that have already formed.  Landscape rocks are one of the most versatile materials that can be used when creating a natural space.  When rocks are exposed to the elements a natural unattractive red staining can occur.  It can come from the rust in the irrigation water and from a chemical reaction between irrigation water and iron that can be present on landscape rocks.  Most stains can be removed by using an oxalic acid bath or a combination of powdered clay and liquid rust remover.  There are also a number of over the counter products that remove rust all of which can be found at local hardware stores

Cleaning Small Landscaping Rocks

To safely clean your landscaping rocks first removal the built-up dirt and debris. Place larger rocks in a bucket.  Put on some rubber gloves and safety goggles combining one gallon of distilled water with one pound of oxalic acid crystals.  Mix carefully with a wooden spoon until crystals are dissolved.  Pour the solution slowly over the landscaping rocks to avoid splashing.  Use enough solution to cover the rocks.  Let this sit until rust no longer remains.  Add baking soda slowly to the oxalic mixture to neutralize it.  This will cause the mixture to bubble and foam up.  Once this process stops you can remove the rocks from the bucket with rubber gloves.  This mixture can be disposed of down the drain.  Rinse the landscape rocks with a garden hose. 

Cleaning Large Landscaping Rocks

Rinse landscape rocks with a garden hose.  Put on rubber gloves and mix rust remover with powdered clay to make a thick paste.  Apply a thick layer to the stains with a spatula.  Allow the paste to sit for 24 to 48 hours.  Cover with plastic wrap or a large tarp to allow the paste to dry completely.  Once the mixture is dry you can scrape it off with a plastic knife.  The rocks should then be washed off with a garden hose.  If rusts or stains remain the process can be repeated. 

Tips for Cleaning Rust

  • Test the acid solution/paste on an area of hidden rocks before cleaning the lot.
  • If the paste leaves marks on the rocks use a wet cloth and polishing powder to buff them out.
  • Always wear rubber gloves and eye protection.
  • Work carefully to avoid splashing on your skin.
  • Use caution to prevent breathing in dust from the oxalic acid and removed paste.
  • While cleaning keep pets and children away from the area.

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditionerswater filtration and purificationreverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.

Improving Water Quality Through Filtration

Take a minute to look inside the tank of your toilet, what do you see?  Do you see a collection of rust, sediment, and/or sand? That same collection of debris is accumulating inside your plumbing and water heater.  It is pretty standard to assume that when any mechanical system in your home becomes saturated with gunk build up the quality of the system and the products of the system are compromised.  The goal for homeowners is to avoid situations where this occurs.  One way this happens is with the installation of a whole house water filter.

When a whole house water filter is installed it can act as a barrier that quietly protects your home.  A filter will prevent crud from settling into the systems throughout your home such as the toilet, water softener, and hot water tanks. 

Benefits of Installing a Water Filter System for Your Home

Layered Protection

With the installation of a whole house water filter system you are layering the protection to your appliances.  You are preventing the sediment from reaching your appliances, plumbing, water softeners, toilets, and such.  Many appliances have small plastic and rubber pieces that are used in the use of different household appliances.  Small amounts of debris will damage seals in appliances over time.  When a seal becomes damaged it will leak and as we all know this ends up costing us time and money.  A filter removes the gunk such as sediments, debris, dirt, and gunk in general.  For homeowners there is an increase in appliance longevity and a piece of mind that your equipment will be reliable for longer. 

Eliminate Unexpected Water Surprises

Both city and well water sources can become compromised from unexpected elements in the system.  When this occurs homeowners can receive quite the surprise at the tap. 

City Water Issues

  • Water Main Break
  • Hydrant Flush
  • New Construction and New Water Connections

All of these events will knock iron and sediment buildup into the water supply.  This in turn creates sludge, orange water, and dirt from coming into your home.

Well water quality is affected by outside sources as well.  The quality of the water can change from season to season. 

A whole house water filter helps to remove the iron that exists in some water sources.  When a water filter is installed the iron in the water is filtered out.  This helps to prevent the staining that occurs on laundry, appliances, faucets, and more.

Filter Operation and Maintenance

Filtration systems function without electricity, without salt, and without waste.  There are no controllers to worry about, batteries to change, or clocks to reset.  In fact, whole house water filtration systems are simple to install and can be added to any water treatment system.  In order to properly maintain a filtration system for your home you will be required to change the filter periodically.  The number of times a filter needs to be changed depends on the quality of the filter, use, and the filters rating.

When choosing a filter consider the following: the physical size of the filter, the Micron rating, flow rate, and filter life.  Larger filters naturally have more surface area which often means that they last longer, increase the quality of the water and water pressure. Larger filtration systems are needed in homes with more than two family members.

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditioners, water filtration and purification, reverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.

Removing Iron and Manganese from Well Water

How many homeowners can honestly say they would be okay drinking water from their taps that comes out brown?  ZERO, that’s how many!  Brown water occurs because of contamination in their water from Iron and Manganese, common elements found in well water.  Thankfully there are water treatment options available to remove these contaminants.  Both Iron and Manganese are found in soil thus washing into the well water drinking supply.  The good thing is that you don’t have to live with contaminants in your water.

Contaminants in your homes water supply certainly can be a nuisance. Iron and Manganese cause several issues including metallic tasting water, stained laundry, clogged plumbing, and an oily or crust sheen on the surface of the water. This is one of the reasons high levels of the contaminants are treated using whole house water treatment systems.

In 1974 the federal government set in place visual standards for water because of the effects of Iron and Manganese.  Although state health-based standards are not in place for metals in drinking water, there are some concerns that high levels of manganese are bad for formula-fed infants. Infant formulas naturally contain manganese, so the National Health Department recommends mixing formula with water with a low manganese level. 

Iron and Manganese Testing

It is easy to recognize elevated levels or iron and manganese in water including a bitter, metallic taste and orangish-brown staining on bathroom fixtures, clothes, and more.  It is however important to test the water before treating it in order to determine the amount of minerals and metals that are in the water.  Two types of metals are commonly found in a homes water supply including reduced and oxidized.  Water that has a reduction in iron and manganese often looks clear, initially however will form solid orangish brown solid particles.  Water with oxidized iron and manganese will have visible particles upon being drawn from the well. 

Water Treatment Options

Once your well water is tested and you are told what type and amounts of iron and manganese are in the water, water treatment specialists like the ones at Reynolds Water Conditioning can help you determine the best treatment option for your home.  It is important to note that some filtration such as oxidation filtration which injects oxygen into the water to remove impurities only removes iron.  The water will need an additional chemical treatment to remove manganese. 

Water softeners are often installed to treat hard water.  They can also remove small amount of iron and manganese.  Water softening units use an ion exchange process which replaces iron and manganese with sodium.  The metals are removed from the softeners filtering resin through a process of backwashing. 

Another treatment option to remove iron and manganese from water is through a point of use reverse osmosis systems.  This treats water at the tap which is usually where drinking and cooking water is drawn from.  The filter uses different membranes to remove unwanted molecules in water to be filtered from the water.  Although this is a fairly simple method of getting water without metal it does not treat water throughout the house.  Thus, staining will still occur in bathrooms and in laundry and water in other parts of the house will have the metallic taste. 

The experts at Reynolds Water Conditioning have a solution to your homes unique water quality needs including: arsenic, bacteria, chlorine, rotten egg smell, fluoride, hard water, iron, lead, acid, tannins, radon, and more.  More information on our water treatment solutions including water softeners and conditioners, water filtration and purification, reverse osmosis drinking water, and iron & odor removal can be found online at https://reynoldswater.com.